FUSION FABRICATION WORKS started its
operation from August 2010 in Chennai, Tamil Nadu, India. The company
was formed by a group of Engineers who are working in Power/Water and
Oil and Gas Industry.
Capability Of The Company
Fusion Fabrication Work Is Capable Of:
- Fabrication of low pressure
(atmospheric) vessels
- Pipe spools
- Chemical dosing skids
- Grille works
- MV/LV electrical panels
- Control panel
- DG synchronization panels
- Supply of electrical and control
components for power, water and oil and gas industry
- Design, Manufacture, Supply & also working as Service Provider of
Jigs and Fixtures (Eg. Drill jigs, Milling fixtures, Welding fixtures
& Pressure testing Fixtures) tailor made to meet clients
requirements.
- Fabrication of Sheet Metal enclosures
- Specialized in Product development for
R&D jobs for any industry.
FUSION FABRICATION WORK- Tool room
is capable of:
- Design, Manufacture, Supply & also working as Service Provider of
Jigs and Fixtures (Eg. Drill jigs, Milling fixtures, Welding fixtures
& Pressure testing Fixtures) tailor made to meet clients
requirements.
- Fabrication of Sheet Metal enclosures
- Specialized in Product development for
R&D jobs for any industry.
COMPANY PROFILE
Profile of The Promoters And
Employees
FUSION fabrication works has been
promoted by Mechanical Engineers, a Mining Engineer and an Entrepreneur. The promoters have more
than 20 years of experience in project development, detail engineering, preparation of design
basis reports, feasibility studies, project management and design reviews of power, water and oil and gas
projects.
Fusion Fabrication Works have employed
well qualified Design and development engineers, Experienced Tool makers, Machinists,
fitters and welders to perform the tool room works and fabrication indicated above and is in
the process of recruiting more staff for this purpose. A certified (level II) quality inspector has also
been employed to ensure good quality of the works being performed.
Machineries And Equipment
- Fusion Fabrication Works Owns The
Following Machineries And Equipment;
- 5T chain pulley block with A frame
arrangement for lifting loads
- 1 no Turret Milling Machine with DRO
- 1 no Horizontal milling machine-medium
duty
- 2 no Light duty lathe-4.5 feet
- 1 no 32mm vertical drilling machine
- 1 no 25mm vertical drilling machine
- 1 no band saw machine
- 1 no surface table for machining work
(650mm square)
- 2 nos. arc/TIG welding machines (3
phase)
- 2 nos arc/TIG welding machine (1 phase)
- 2 no. MIG welding machine
- 1 no. Plasma cutting machine (for CS
and SS)
- 1 no. Structural steel and pipe cutting
machine
- 1 gas cutting set
- 1 no. Pug cutting machine
- 1 no. 3hp air compressor (with micron
filter (for oil) and dryer) for plasma cutting machine
- Manual sheet cutting machine
- 1 no. hand fly press
- Adequate number of grinding machines
- Required accessories for mechanical and
electrical welding works
- Required PPE for performing the
fabrication works
- Tool Room machineries and tools such as
verniers/screw gauge/height gauge etc.
Fabrication Workshop Information
The Fabrication workshop has boundary
walls on all four sides with adequate access for vehicles into the
premises for loading and unloading. The workshop has a watchman room,
toilets and bathroom. The workshop is located in the north of Chennai
approximately 35 kilometers from the city in SIDCO industrial estate.
The workshop is well connected by roads.
- Total area of the workshop premises-
10000 sqft
- Builtup area-1300 sqft
- Outdoor area available for fabrication-
approximately 8700 sqft
The machine shop (tool room shop) is
around 250 sqft housing lathe, drilling machine and tool room
equipment. Space for addition of additional machines is also
available.
General Information
FUSION FABRICATION WORKS is registered
with the sales and service tax departments and holds a valid registration number.
Send Inquiry
Send Inquiry
